Home     Yaesu FT DX 3000 HF/50 MHz 100W Transceiver
Yaesu FT DX 3000 HF/50 MHz 100W Transceiver

Yaesu FT DX 3000 HF/50 MHz 100W Transceiver


Yaesu FT DX 3000 HF/50 MHz 100W Transceiver

The NEW FT DX 3000 Transceiver is the latest addition to the Yaesu family of fine Amateur Radios, incorporating the newest down conversion and sharp edged crystal roofing filter technology. These features provide outstanding receiver performance which is a heritage of the FT-DX5000. Our new transceiver also incorporates many other new features in a compact housing.
Technische Details Yaesu FTDX-3000D
General
RX Frequency Range
30 kHz - 56 MHz (operating)
1.8 - 54 MHz (specified performance, Amateur bands only)
TX Frequency Ranges
1.8 - 54 MHz (Amateur bands only)
Frequency Stability
±0.05 ppm (after 1 minute @ -10 °C ~ +50 °C)
Operationg Temperature Range
-10 °C ~ +50 °C
Emission Modes
A1A (CW), A3E (AM), J3E (LSB, USB), F3E (FM),
F1B (RTTY), F1D (PACKET), F2D (PACKET)
Frequency Steps
1/10 Hz (SSB,CW, & AM), 100 Hz (FM)
50 Ω, unbalanced
16.7 - 150 Ω, unbalanced (1.8 - 29.7 MHz)
25 - 100 Ω, unbalanced (50 - 54 MHz)
(Tuner ON, 1,8 - 50 MHz Amateur Bands, TX only)
Power Consumption
Rx (no signal) 1,8 A
Rx (signal present) 2,1 A
Tx (100 W) 23 A
Supply Voltage
DC 13,8 V ±10% (Negative Ground)
Dimensions (WxHxD)
365 x 115 x 312 mm w/o knob and connector
Weight (approx.)
10 kg

Transmitter
Power Output
5 - 100 Watt (CW, LSB, USB, FM, RTTY, PKT)
2 - 25 Watt (AM carrier)
Modulation Types
J3E (SSB): Balanced
A3E (AM): Low-Level (Early Stage)
F3E (FM): Variable Reactance
Maximum FM Deviation
±5.0 kHz / ±2.5 kHz
Harmonic Radiation
Better than -60dB (1.8 - 29.7 MHz Amateur bands: Harmonics)
Better than -50dB (1.8 - 29.7 MHz Amateur bands: Others)
Better than -65dB (50 MHz Amateur band)
SSB Carrier Suppression
At least 60 dB below peak output
Undesired Sideband Suppression
At least 60 dB below peak output
Audio Response (SSB)
Not more than -6 dB from 300 to 2700 Hz
3rd-order IMD
-31 dB @14 MHz, 100 watts PEP
Bandwidth
500 Hz (CW)
3.0 kHz (LSB, USB)
6.0 kHz (AM)
16 kHz (FM)
Microphone Impedance
600 Ω (200 to 10 k Ω

Receiver
Circuit Type
Double-conversion Superheterodyne
Intermediate Frequencies
9 MHz/30 kHz (24 kHz for AM/FM)
Sensitivity
SSB (2.4 kHz, 10 dB S+N/N)
4 μV (0.5 - 1.8 MHz, IPO "ON")
0.16 μV (1.8 - 30 MHz, RF AMP2 "ON")
0.125 μV (50 - 54 MHz, RF AMP2 "ON")
AM (BW: 6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz)
28 μV (0.5 - 1.8 MHz, IPO "ON")
2 μV (1.8 - 30 MHz, RF AMP2 "ON")
1 μV (50 - 54 MHz, RF AMP2 "ON")
FM (BW: 15 kHz, 12 dB SINAD)
0.5 μV (28 - 30 MHz, RF AMP2 "ON")
0.35 μV (50 - 54 MHz; ARF MP2 "ON")
There is no specification in frequency ranges not listed.
Selectivity (WIDTH: Center):
Mode
-6 dB
-60 dB
CW/RTTY/PKT
0.5 kHz or better
750 Hz or less
SSB
2.4 kHz or better
3.6 kHz or less
AM
6 kHz or better
15 kHz or less
FM
12 kHz or better
30 kHz or less
Image Rejection
70 dB or better (1.8 - 30 MHz amateur bands
60 dB or better (50 - 54 MHz Amateur band)
Maximum Audio Output
2.5 W into 4 Ω with 10% THD
Audio Output Impedance
4 to 8 Ω (4 Ω nominal)
Conducted Radiation
Less than 4 nW


Rugged 100 Watt Output Power


The Amazing Crystal Roofing Filter performance has been proven in the FT DX 5000
The Down conversion 9 MHz 1st IF frequency receiver construction can realise narrow 300 Hz (optional), 600 Hz and 3 kHz bandwidth roofing filters.

Implementing the extra sharp Crystal Roofing Filters provides superior close-in dynamic range and affords the best receiver performance possible.

Outstanding Receiver performance is the heritage of the FT DX 5000
The Essential elements in receiver performance are the RF amplifier and the 1st mixer.

The RF Amplifier has optimized NF points, and the over-sized wide range RF transformer exhibits minimum saturation in strong signal processing. The optimized devices were selected to guarantee superior multi-signal RX performance.

The desired maximum performance has been realized in the development of the FT DX 3000 receiver circuitry. This new radio has the high dynamic rance IP3 performance that was realized and proven in the FT DX 5000.

IF DSP provides effective and optimized QRM rejection
The 32 bit high speed floating decimal DSP (max 2800 MIPS) provides effective cancellation/reduction (DNR) of the random noise that is frequently found on the HF Frequencies.

Auto-Notch (DNF) that automatically eliminates the dominant beat tone

CONTOUR and APF; very effective receiver noise reduction tools in the HF band operations.

Yaesu original DSP QRM and noise reduction are also provided with the new FT DX 3000.

Large and Wide Colour LCD Display
The high-resolution (480 x 272 dots) 3.5-inch wide colour LCD displays the operating information and the status of the transceiver functions.

The various FT DX 3000 functions are displayed on this LCD and provide the operator with easy to read operating information.

High Speed Spectrum Scope built-in
Although the FT DX 3000 only has one receiver, a high speed Spectrum Scope is built into the radio.

When in Auto Mode, the Spectrum Scope display is updated in real time.

The maximum bandwidth of the scope is 1 MHz, and the minimum span width setting is 20 kHz. The best desired span is selectable for the high-resolution display. The current band activity can be monitored in real time.

AF SCOPE display and RTTY/PSK encoder/decoder (optional)
The optional AF SCOPE and optional RTTY encoder/decoder functions have been developed for the FT DX 3000.

The wave form of the AF SCOPE signal can be displayed on the TFT LCD. Also, the RTTY/PSK text may be displayed on the LCD.


Independent Frequency Display
The Main operating frequency is the most important display in the radio, with VFO-A frequency located just above the main dial.

The newly-developed LCD has a wider viewing angle and higher contrast for convenient and effortless viewing.

Other Features


  • Built-In Specialised Receiver amplifier for 50 MHZ
  • Three antenna connectors are provided, with the possibility of assigning the "ANT-3" connector to "RX-Only"
  • Signal output for an external receiver
  • 9 MHz IF output
  • High Speed Automatic antenna tuner built-in
  • Optional µ-tune unit available
  • USB Interface
FT DX 3000 Brief Description

Rugged 100 Watt Output Power


The Amazing Crystal Roofing Filter performance has been proven in the FT DX 5000
The Down conversion 9 MHz 1st IF frequency receiver construction can realise narrow 300 Hz (optional), 600 Hz and 3 kHz bandwidth roofing filters.

Implementing the extra sharp Crystal Roofing Filters provides superior close-in dynamic range and affords the best receiver performance possible.

Outstanding Receiver performance is the heritage of the FT DX 5000
The Essential elements in receiver performance are the RF amplifier and the 1st mixer.

The RF Amplifier has optimized NF points, and the over-sized wide range RF transformer exhibits minimum saturation in strong signal processing. The optimized devices were selected to guarantee superior multi-signal RX performance.

The desired maximum performance has been realized in the development of the FT DX 3000 receiver circuitry. This new radio has the high dynamic rance IP3 performance that was realized and proven in the FT DX 5000.

IF DSP provides effective and optimized QRM rejection
The 32 bit high speed floating decimal DSP (max 2800 MIPS) provides effective cancellation/reduction (DNR) of the random noise that is frequently found on the HF Frequencies.

Auto-Notch (DNF) that automatically eliminates the dominant beat tone

CONTOUR and APF; very effective receiver noise reduction tools in the HF band operations.

Yaesu original DSP QRM and noise reduction are also provided with the new FT DX 3000.

Large and Wide Colour LCD Display
The high-resolution (480 x 272 dots) 3.5-inch wide colour LCD displays the operating information and the status of the transceiver functions.

The various FT DX 3000 functions are displayed on this LCD and provide the operator with easy to read operating information.

High Speed Spectrum Scope built-in
Although the FT DX 3000 only has one receiver, a high speed Spectrum Scope is built into the radio.

When in Auto Mode, the Spectrum Scope display is updated in real time.

The maximum bandwidth of the scope is 1 MHz, and the minimum span width setting is 20 kHz. The best desired span is selectable for the high-resolution display. The current band activity can be monitored in real time.

AF SCOPE display and RTTY/PSK encoder/decoder (optional)
The optional AF SCOPE and optional RTTY encoder/decoder functions have been developed for the FT DX 3000.

The wave form of the AF SCOPE signal can be displayed on the TFT LCD. Also, the RTTY/PSK text may be displayed on the LCD.

Independent Frequency Display
The Main operating frequency is the most important display in the radio, with VFO-A frequency located just above the main dial.

The newly-developed LCD has a wider viewing angle and higher contrast for convenient and effortless viewing.

Other Features


  • Built-In Specialised Receiver amplifier for 50 MHZ
  • Three antenna connectors are provided, with the possibility of assigning the "ANT-3" connector to "RX-Only"
  • Signal output for an external receiver
  • 9 MHz IF output
  • High Speed Automatic antenna tuner built-in
  • Optional µ-tune unit available
  • USB Interface
Specifications

FT DX 3000 Transceiver

GENERAL

Rx Frequency Range
30 kHz - 60 MHz (Operating)

1.8 - 54 MHz (Specified performance, Amateur Bands only)
Tx Frequency Range
1.8 - 54 MHz (Amateur Bands only)
Frequency Stability
±0.5ppm (after 1 minute @ -10ºC to +50ºC)
Operating Temperature Range
-10ºC to +50ºC
Emission Modes
A1A (CW), A3E (AM), J3E (LSB,USB), F3E (FM), F1B (RTTY),

F1D (Packet), F2D (Packet)
Frequency Steps
1/10Hz (SSB, CW, AM), 100Hz (FM)
Antenna Impedance
50Ω, unbalanced

16.7Ω - 150Ω, unbalanced (1.8 - 29.7 MHz)

25Ω - 100Ω, unbalanced (50 - 54 MHz)

(Tuner ON, 1.8 MHz - 50 MHz Amateur bands, TX only)
Power Consumption
Rx (no signal) 1.8 A
(approximate figures)
Rx (signal present) 2.1 A

Tx (100W) 23 A
Supply Voltage
DC 13.8 V ±10% (Negative Ground)
Dimensions (W x H x D, mm)
365 x 115 x 312
Weight (approx, kg)
10
TRANSMITTER

Power Output
5 - 100 Watts (2 - 25 Watts AM carrier)

5 - 50 Watts (AM carrier)


Modulation Types
J3E (SSB): Balanced

A3E (AM): Low-Level (Early Stage)

F3E (FM): Variable Reactance
Maximum FM Deviation
±5.0kHz/±2.5kHz
Harmonic Radiation
Better than -60dB (1.8 - 29.7 MHz Amateur bands: Harmonics)

Better than -50dB 1.8 - 29.7 MHz Amateur bands: Others)

Better than -65dB (50 MHz Amateur band)
SSB Carrier Suppression
At least 60dB below peak output
Undesired Sideband Suppr.
At least 60dB below peak output
3rd-order IMD
-31dB @ 14 MHz 100 watts PEP
Bandwidth
3kHz (LSB/USB), 500Hz (CW), 6kHz (AM), 16kHz (FM)
Audio Response (SSB)
Not more than -6dB from 300 to 2700 Hz
Microphone Impedance
600Ω (200 to 10kΩ)
RECEIVER

Circuit Type
Double-Conversion Superheterodyne
Intermediate Frequencies
9.000 MHz / 30 kHz (24 kHz for AM/FM)
Sensitivity
SSB (BW: 2.4 kHz, 10dB S+N/N)

4µV (0.5 - 1.8 MHz, IPO "ON")

0.16µV (1.8 - 30 MHz, RF AMP2"ON")

0.125µV (50 - 54 MHz, RF AMP2"ON")

AM (BW: 6 kHz, 10dB S+N/N, 30% modulation @ 400 Hz)

28µV (0.5 0 1.8 MHz, IPO"ON")

2µV (1.8 - 30 MHz, AMP2"ON")

1µV 50 - 54 MHz, AMP2"ON")

FM (BW: 15 kHz, 12 dB SINAD)

0.5 µV (28 - 30 MHz, AMP2"ON")

0.35 µV (50 - 54 MHz, AMP2"ON")

* There are no specifications in frequency ranges not listed *
Selectivity (WIDTH: Centre)
Mode -6db -60dB

CW/RTTY/PKT 0.5kHz or better 750Hz or less

SSB 2.4kHz or better 3.6kHz or less

AM 6kHz or better 15kHz or less

FM 15kHz or better 25kHz or less
Image Rejection
70dB or better (1.8 - 30 MHz Amateur bands)

60dB or better (50 - 54 MHz Amateur band)
Maximum Audio Output
2.5W into 4Ω with 10% THD
Audio Output Impedance
4 to 8Ω (4Ω: Nominal)
Conducted Radiation
Less than 4 nW





Specifications are subject to change, in the interest of technical
improvement, without notice or obligation, and are guaranteed
only within the Amateur Bands.


€ 2290.00


Tijdelijk niet leverbaar


Yaesu FT DX 3000 HF/50 MHz 100W Transceiver